- Parts came in!
- Engine Noise BAD
- Engine hesitates, sputters
- oil pump?
- Won't Start
- No compression in cylinder 2
- piston clearances help
- Engine wont run off full choke
- Engine rebuild...
- Parts swap info
- Oil Pump mods
- 1984 t type engine rebuild
- Its out
- Rear Main Leak
- set timing
- Oil Leak
- early g/n motor ?
- multiple issues 87 T-Type
- turbo drain tube
- Needs some assistance with PN's
- Firing Up the Buick
- Smoking and oil burning
- Rear main seal issue
- recommended motor oil and filter?
- Stock or stage one
- serpentine belt crawling towards engine
- Postons GN 107 T cam specs.
- Lifter experts, come in!
- dry gaskets?
- need help crank sensor
- Aftermarket cam??
- AC Delco PF52 vs. PF52E
- T-Type Modifications
- Oil pump/ oiling issues period!
- Timing Chain
- oil catch can setup
- Need some input for J&E Pistons. What do you guys want to see from them...
- Valve Cover Change
- 8445 heads - dual valve springs?
- RJC power plate
- EGR Valve
- Valve springs
- Need help with cam selection
- Replacing timing chain cover
- 4.1 block
- Balance
- Chicken or the egg.....or apples and oranges?
- Engine VIN stamp (Was: Re: How Many WE4"s are all black)
- Newbe Needs Some Help
- Frame Brackets for Motor Mounts
- Diffent ESC and Coils Pack, Etc.
- What does EV6 Mean on Engine Block
- Hardware help again
- Engine oiling
- Small Problem Maintenance Question
- GN performance iron heads
- 1985 Grand National Heads
- gn1 champion heads
- Throttle body spring placement
- Help with 109 block
- Cold idle issues
- Water Leak from hood?
- Replacing the Fan Clutch
- Perfect at 70-80 mph - tractor at stop light
- IAC adapter
- Buick GN head gasket choice
- Wantin new valve springs???????
- stock intake manifold
- Idiot needs assistance
- oil fill
- Stock Everything.. just getting started...
- Stock cams - carbed vs turbo vs roller FWD vs non-roller FWD vs.. etc.
- 86 GN - engine lift loop locations
- 3.8 vs 4.1
- Need help with sprucing up my motor
- tensioner arm/pulley issue?
- oil pump oil leak....geez
- Need new engine block!!!
- engine builders
- timing chain.
- need Help identifying turbo & injectors
- Autograph on Dash
- idle adjustment
- what pistons to use
- Can you help id engine
- Stock head valve undercut
- heater control valve
- electrical short
- intake porting?
- 14 bolt block timing cover
- rear main seal question
- Used engine rebuild what to do
- Lt1 valve springs
- New Comp Cam break in
- Oil pressure
- timing chain issue
- oil pan issue
- Push Rod Missing
- #4 is a dead hole
- Valve seals
- Rattle from passenger side of engine
- Block ID
- Sourcing a hot air throttle body re-bushing
- Alternator pulley problems
- Oil on lower radiator hose
- New engine build
- Total seal piston rings
- Block preparation
- Champion head identification
- Roller rocker identification
- Rocker shaft supports
- Removing plenum and throttle body help
- Throttle Body help
- Vacuum block sizes
- Engine noise? Timing chain?
- oil pickup screen
- Belt tensioner comes loose
- Oil leak possibility?
- Hydraulic Cam recommendation
- Crank selection
- rebuilding motor
- roller rockers
- Valve Cover Gaskets
- Oil pan gasket
- Ticking Noise Diagnosis
- Back pressure combo?
- Roller cam selection
- OIL FOR Rebuilt Motor
- Stage two heads
- New stroker motor
- Valve Spring Baffles?
- camshaft ticking noise
- Injectors
- Positive ventilation crankcase issue
- Engine stopped on roadway