Parting out

[67TurboCamaro]

I am parting out a complete car minus engine and interior. The car is solid, from what I can tell there is no rust anywhere. Here is a partial list of what I have-

86-87 body parts-

Body with 6 point cage
Header panel
Headlight bezels
front bumper (GN)
87 grille (sold)
doors complete w/good power windows
front and rear glass blackout trim
fenders
hood (has some dings and center support cut out) will not ship!!
rear spoiler complete (all 5 pieces) -$250
rear bumper (GN)
Tailights

Drivetrain

Powerstroke I/C with pipes
Complete 8.5" posi rear
400 chevy transmission and 3500 converter
3.5" aluminum driveshaft for 400 trans
400 BOP switch pitch trans and converter with 1600/4000 stall, 5 miles on rebuild. (trans does need minor repair, wouldn't switch to high stall)
Centerline Autodrags- 15x3 w/ new 165 tires, and 15x8 with shot 28x10.5 slicks-$300

Misc

Gn steering column w/tilt&cruise
GN shifter
stock gas tank with welded in sump
86-87 wiring harness
driveshaft loop (sold)
radiator
MAF translator with LS1 MAF-$200 (sold)
Xtender extreme chip for 83# injectors-$75
Scanmaster not sure what version, it came in a car I bought.-$200
Air bags (no hardware)-$50
Fuel sender with Walbro 340-$150
Single guage pillar pod-$15
30# injectors and Kenne Bell chip
radiator hold down- $40

Please, NO TIRE KICKERS!!

[1986GN]

How Mutch For Engine Harness And What Condition Is It In Thanks Gilbert

[Dustin86ttpye]

will you do any better on your scanmaster?

[67TurboCamaro]

$175+shipping on scanmaster.

I will have to look at the wiring harness and see what kind of shape it is in.

[dwall]

Interested in price and shipping for the following:

front bumper (GN)
doors complete w/good power windows

Thanks

[67TurboCamaro]

The bumper is straight, but would need repainted. I can send you some pics if you want. $75 +shipping

I would take $300 per door or $500 for the pair +shipping.

Give me your adress and I will figure shipping.

[67TurboCamaro]

How Mutch For Engine Harness And What Condition Is It In Thanks Gilbert
Harness has several cuts and splices. $150??+shipping

[snoxer]

Do the head lamp bezels have marker lights? How much shipped to 48185? Do you have the trans cooler elbows and short lines that come out of the rad? If so, how much?

Craig

[67TurboCamaro]

Bezels are sold pending payment. Sorry, I don't have the lines or elbows, the car had an aftermarket cooler.

[quick hot air]

I need the b pillar trim for a hard top car. Can you help??

[67TurboCamaro]

I am not sure exactly what you need. Can you describe them.

[quick hot air]

It is the trim piece between the the front side window and the rear side window that the weather stripping is connected to. Im not sure what the right name of the part is. Thanks.

[67TurboCamaro]

It is the trim piece between the the front side window and the rear side window that the weather stripping is connected to. Im not sure what the right name of the part is. Thanks.
Sorry mine are chrome.

[monzaz]

Hey where are you located? How much for the diff. Looking for a good housing(s) to build. Let me know what you have to get back on the road again.

[67TurboCamaro]

Hey where are you located? How much for the diff. Looking for a good housing(s) to build. Let me know what you have to get back on the road again.
Elizabethtown, KY. $850 for the rearend. I know where there is a 7.5", 3.73 posi. If your interested I will get you a price.

[Avery's 86 GN]

do you stiil have the column?

[67TurboCamaro]

do you stiil have the column?
Yes, still have it.

[kingcrab54]

Body with cage?

How complete? any pics?

I from OHIO North West Corner!

[Avery's 86 GN]

Yes, still have it.


how much? and do you still have the steering wheel?

[turbomonte]

How much for the chip and 30lb injectors.

[67TurboCamaro]

Injectors and chip have been sold.

$100+shipping for column. I have a steering wheel, but it is kind of rough, $30.

I just got back from BPG with it, it isn't very complete anymore!! I sold the fenders, pass door, hood, header panel, and front fillers. I need $1200 for whats left. It still has the 8.5" posi.

[Avery's 86 GN]

Injectors and chip have been sold.

$100+shipping for column. I have a steering wheel, but it is kind of rough, $30.


i'll take the colunm,how do i pay u? is the steering wheel a gn steering wheel ?if so do you have any pics or can you describe "rough"?

[67TurboCamaro]

I can take a M/O or Paypal, but if you use Paypal I ask that you cover there fee's. I will get you some pics of the steering wheel. Once I get the column out I will be able to get you a total with shipping.

[Avery's 86 GN]

10-4 :shiny:

[67TurboCamaro]

PM or email me your address and I will get you a shipping quote.

[Avery's 86 GN]

PM or email me your address and I will get you a shipping quote.


pm sent
Thanks

[El Grande]

Are you willing to cut the hood bump off, and ship?

[isaacsracing]

Do you still have the rear spoiler??? Take $175.00 cash and i will come and pick it up this weekend. I am in Danville KY???

[67TurboCamaro]

Hood and spoiler are already sold.

[dvsgn]

HOw many miles on that walbro 340 pump? e mail me please kwik6@gmail.com

[67TurboCamaro]

HOw many miles on that walbro 340 pump? e mail me please kwik6@gmail.com
The pump came with a stage II car that I bought, so I don't know exactly how many miles it has on it. The guy I got it from said it wasn't very old. He switched to an external pump and sumped tank.

[Art1984]

Do you still have the header panel if so how much shipped to Bellevue NE 68123

[tntshort]

How much for the header panel?
Thanks,Tyson

[GNsniperdfa1]

Hi, how much for the header panel shipped to 60616?

Thanks

[kane123]

How much for the GN shifter shipped to 17702

[67TurboCamaro]

How much for the GN shifter shipped to 17702

Wow, I thought this thread died long ago. The car and 90% of the parts are long gone. I do still have the shifter, I would take $65 shipped for it.

[kane123]

can you send me a pic or two?